- Home /
- Prodotti /
- Studio e registrazione /
- Interfacce audio /
- Accessori e parti di ricambio per interfaccia audio /
- Focusrite /
- Focusrite ADN2 AD Expansion Card for Focusrite ISA One preamp
Focusrite ADN2 AD Expansion Card for Focusrite ISA One preamp
Descrizione
The introduction of this Focusrite ADN2 AD expansion module means you can finally integrate the classic ISA One microphone preamp into your Dante network. This two-channel A/D card offers superb analogue-to-digital conversion for the ISA One and supports sample rates of up to 24-bit/192kHz as well as AES3, ADAT and S/PDIF connections. More specifically, the ADN2 AD is equipped with two RJ45 ethernet ports, an AES3 XLR output, a Toslink ADAT output and an S/PDIF RCA output. Focusrite have even fitted two BNC ports to accommodate word-clock synchronisation between external devices, while the Dante outputs are naturally compatible with RedNet and Red interfaces, as well as other Dante-ready gear. RedNet Control and Dante Controller software included.
Specifiche
Caratteristiche
- Sustainable product not specified
- Tipo di protezione not applicable
- Tipo di accessorio per interfaccia audio modulo I/O
Peso e dimensioni imballaggio incluso
- Peso (imballaggio incluso) 900 gr
- Dimensioni (imballaggio incluso) 27,0 x 21,5 x 7,0 cm
Specifiche
- Focusrite ADN2 AD expansion module
- suitable for ISA One preamp
- two channels with extremely high audio quality thanks to analogue to digital conversion
- 24-bit/192kHz sample rate
- Dante connectivity via 2x RJ45 ethernet ports
- 2-channel XLR connectors for AES3 signal output
- 2-channel RCA connectors for S/PDIF signal output
- 2-channel Toslink connectors for ADAT signal output
- word clock i/o via BNC connectors for synchronisation of external gear
- RedNet Control and Dante Controller software included for routing and control
Recensioni
Recensioni da altri paesi
Tradurre tutte le recensioni in Italiano
Pacchetto convenienza
Focusrite ADN2 AD + Focusrite ISA One
- 1 x Focusrite ADN2 AD Expansion Card for Focusrite ISA One preamp € 879,00
- 1 x Focusrite ISA One preamplificatore microfonico € 639,00
Altri prodotti Focusrite
Vedi tutti i prodotti Focusrite
Prodotti alternativi di altre marche
Vedi tutti i prodotti nella categoria Accessori e parti di ricambio per interfaccia audio
This interface card gives your Focusrite ISA one a digital interface.
-The card comes in a box protected by an ESD bag, including a clear install manual.
- The installation takes less than 5 minutes; unscrew the lid by removing 8 screws, removing the backpanel by removing 3 screws and install the module with the incuded 4 new (additional) screws. Connect the flatcable connector and close the enclosure. Handeling the electronics causes risk for ESD, so that's a smal thing to keep in mind.
- Initialising the card was easy by pressing Ext and turning on the device. The ADN2 was recognised instantly, also showing up in your Dante Controller window.
- All features can be controlled within the Dante Controller window, so there is no need to have the Focusrite REDNET software installed. If you do use REDNET then the device is also recognised in that software as wel, athough REDNET does not provide additional features.
- The card provides a stereo (L+R) DANTE ouput, as shown in DANTE controller. The Focusrite ISA One signal is send digitaly in mono over the Left channel.
- Note that the ADN2 AD output level is 'fixed'; there is no (software) output level control (gain/attenuation level).
This card is usefull for eliminating cabling between Focusrite ISA one and your AD/Soundcard, preventing possible noise injection and clarity filtering by the audiocable impedance & capacitance.
The sound quality of this ADN2 AD is very transpartant and clear.
It is pricy, but is it worth it!